Форум гитаристов

Global - Out1 (Out2) EQ

... и добавил:

Безустанный Клиф ))) но, к сожалению, только для владельце XL и XL+


Axe-Fx II "Quantum" Rev 6.00 Public Beta

XL:
www.fractalaudio.com/downloads/firmware-presets/axe-fx-2/Quantum/6.0/axefx2_xl_Quantum_6p00.syx

XL+:
www.fractalaudio.com/downloads/firmware-presets/axe-fx-2/Quantum/6.0/axefx2_xlplus_Quantum_6p00.syx

At this time there is no Mark I/II version as I could not get the firmware to fit in memory. I will continue to work on methods over the coming weeks to remedy this but there are no guarantees that it will be possible.


Release Notes:

6.00

Greatly improved Wah block. Two new parameters have also been added: “Coil Bias” parameter allows the user to adjust the DC offset of the virtual inductor. “Low Cut Freq” sets the highpass filter due to the input coupling capacitor. It is recommended that existing presets be auditioned and, in most cases, deselecting and reselecting the desired model to reset dependent parameters.

Improved Amp block output transformer to power tube interaction modeling. This results in less “smear” in the overtones when the virtual power tubes are driven into clipping.

Improved Amp block plate clipping modeling. New algorithms more accurately replicate the gradual onset of clipping and never fully hard clip resulting in a more dynamic and “open” tone. Note that the increased dynamics may result in some amp models having higher peak volumes which can result in clipping with existing presets. To remedy this simply turn down the Level control in the Amp block.

Recalculated Amp block preamp tube parameters. The “12AX7A SYL” (Sylvania 12AX7A) is now the default type as we think it sounds the best.

Improved background calculation accuracy for cathode follower parameters.

Added Solo 88 tone stack type (the Solo 88 Rhy and Lead models previously used the Solo 100 tone stack which has a different treble taper and load resistance). The Solo 88 Rhy and Lead models now default to that tone stack type.

Added Monitor tab to Tone Match block. This tab allows the user to monitor the difference in frequency response in real time. This can be used when matching real amps to identify differences in tone stack response due to manufacturing tolerances, etc.

Fixed wrong snubber cap value in Recto 2 amp models. This changes the default High Cut value to 10 kHz.

Fixed bug that could possibly cause crashes/lockups.


NOTE:

This update will NOT change the sound of existing presets as the amp modeling version will automatically be set to the version when the preset was created. To use the new amp modeling set the Modeling Version parameter in the Amp block to “Latest”. When selecting new amp models the Modeling Version will be set according to the Default Modeling Version in the Global menu.

Вот и все, похоже что на этом обновления для mark1 и mark2 перестанут выходить, тем самым устройства становятся устаревшими.

Вот и все, похоже что на этом обновления для mark1 и mark2 перестанут выходить, тем самым устройства становятся устаревшими.

Уже нет.

Клифф написал 25 минут назад:

The Quantum 6.00 build is up. To get it to fit in the Mark I/II the ability to use older Modeling Versions was removed but ONLY for the Mark I/II. This required a lot of #ifdef's but I managed to do it.

Now let's talk about some more interesting things.

... и добавил:

6.0 зарелизили. Для Марков тоже. 

vangrieg,
Точно, есть релиз !!!

Mark I/II:
www.fractalaudio.com/downloads/firmware-presets/axe-fx-2/Quantum/6.0/axefx2_Quantum_6p00.zip

XL:
www.fractalaudio.com/downloads/firmware-presets/axe-fx-2/Quantum/6.0/axefx2_xl_Quantum_6p00.zip

XL+:
www.fractalaudio.com/downloads/firmware-presets/axe-fx-2/Quantum/6.0/axefx2_xlplus_Quantum_6p00.zip

NOTE:
The Mark I/II does not support the Modeling Version controls and uses the latest algorithms by default.


Axe-Fx II Quantum Firmware Release Notes
*******************************************************************************
6.00

Greatly improved Wah block. Two new parameters have also been added: “Coil Bias” parameter allows the user to adjust the DC offset of the virtual inductor. “Low Cut Freq” sets the highpass filter due to the input coupling capacitor. It is recommended that existing presets be auditioned and, in most cases, deselecting and reselecting the desired model to reset dependent parameters.

Improved Amp block output transformer to power tube interaction modeling. This results in less “smear” in the overtones when the virtual power tubes are driven into clipping.

Improved Amp block plate clipping modeling. New algorithms more accurately replicate the gradual onset of clipping and never fully hard clip resulting in a more dynamic and “open” tone. Note that the increased dynamics may result in some amp models having higher peak volumes which can result in clipping with existing presets. To remedy this simply turn down the Level control in the Amp block.

Recalculated Amp block preamp tube parameters. The “12AX7A SYL” (Sylvania 12AX7A) is now the default type as we think it sounds the best.

Improved background calculation accuracy for cathode follower parameters.

Added Solo 88 tone stack type (the Solo 88 Rhy and Lead models previously used the Solo 100 tone stack which has a different treble taper and load resistance). The Solo 88 Rhy and Lead models now default to that tone stack type.

Added Monitor tab to Tone Match block. This tab allows the user to monitor the difference in frequency response in real time. This can be used when matching real amps to identify differences in tone stack response due to manufacturing tolerances, etc.

Fixed wrong snubber cap value in Recto 2 amp models. This changes the default High Cut value to 10 kHz.

Fixed wrong phase inverter component value in all “Plexi 50W” amp models. Probably not audible though.

Fixed bug that could possibly cause crashes/lockups.


NOTE:
This update will NOT change the sound of existing presets as the amp modeling version will automatically be set to the version when the preset was created. To use the new amp modeling set the Modeling Version parameter in the Amp block to “Latest”. When selecting new amp models the Modeling Version will be set according to the Default Modeling Version in the Global menu. This option is only available on XL and XL+ models.

я не обновляюсь с 2.04 до сих пор.

Та может и ни к чему) Я вчера только обновился ради интереса с 2.03 до 5.03.

vangrieg,, ну, потеря наруленных ранее пресетов, например. У меня Mark II.

Вот когда крутилки не было,  да, это была целая эпопея иной раз.

теперь она опять исчезла для Марк I/II.

Tauric, ну, выбор firmware, чтобы пресеты не менялись.vangrieg, да, только сейчас, но я однажды очень сильно попал таким образом. Неделю сидел перекручивал. И с тех пор, где-то в глубине души сидит непреодолимый страх 

Tauric, ну, выбор firmware, чтобы пресеты не менялись.

А где это выбирать?