Вышло обновление прошивки 12! ) Качаем:)
Added On/Off switch for the Metronome.Дождались!
... и добавил:FIRMWARE RELEASE NOTES
🟡 Make Backups - As always, use Fractal-Bot in FM3-Edit to back up your System and Presets prior to upgrading.
🟡 Upgrading from version 9.01 or older? Please SCROLL DOWN and read the release notes for version 10.0 VERSION 12.0 | January 19, 2026
🔴 IMPORTANT: This update adds new DynaCab™ models to the FM3, bringing it in sync with the Axe-Fx III and FM9. To make room, the number of User Cab slots has been reduced from 1024 to 512. If you have any User Cabs stored in slots 513–1024, please back them up using FM3-Edit. Those slots will be removed, and any cabs in them will be permanently lost after the update. This version uses FM3 DynaCabs 1.09.
The FM3 is now up to date with Axe-Fx III fi rmware release 31.03.
NEW FEATURES & UPDATES
AMP BLOCK UPDATES
● New “Deluxe 6G3” amp model based on the bright channel of a 6G4 “Brownface” Deluxe.
● Improved Preamp Modelling - Delivers more accurate harmonic response and improved feel, especially as an amp is driven harder (for example, when using a boost or overdrive).
● Improved Phase Inverter modeling. Went through every model with a fi ne-toothed comb and adjusted power amp and phase inverter parameters as needed to refl ect new modeling.
NOTE: The Preamp Tube Hardness parameter functions differently now. Existing presets are automatically updated to the default value for the selected amp model.
● Improved Power Amp Modeling brings a more controlled low end, especially for non- Master Volume amps.
● Added “Suhr Reactive Load” Speaker Impedance Curve.
NEW DRIVE PEDAL MODELS
● New “PI Fuzz – Bass” model based on a Deluxe Bass Big Muff Pi.
● New “NoAmp Bass DI” based on a SansAmp™ BassDriver DI.
● New “NoAmp Bass Pre” based on a SansAmp™ BassDriver DI with the speaker emulation bypassed. This can be used into a Cabinet block or as a boost into an Amp block.
● New “Royal Bass DI” based on a Noble™ Bass Preamp DI. The model has been modifi ed with more gain so that it can be overdriven. With the Drive knob at 5.00 the gain is the same as the actual preamp. Also, instead of a Low Cut switch, the model uses an adjustable Low Cut control.
NEW EFFECT MODELS
● New “Citrus Juicer” in the Compressor block, based on the Dan Armstrong Orange Squeezer™. The original pedal has a single knob, but the model adds additional parameters for extended fl exibility. On the original, the ratio and threshold vary with the specifi c components used and the internal bias trim. As a starting point, set Threshold to –26.0 dB and Compression to 8.0, then adjust to taste. The new Half-Wave detector type used by this model is also available for other compressor types, offering different attack and release behavior and a slightly grittier character.
● New “7 Band Pedal” in the GEQ Block, based on a Boss™ GE-7.
● New “7 Band Bass Pedal” in the GEQ Block, based on a Boss™ GE-7B.
● New “Surround Delay” type in the Delay block. This type produces “rotating” echoes that seem to move around the listener. The Rotation parameter determines how rapidly the echoes rotate. With Rotation at 100% the echoes rotate 180 degrees each time (front, back, front, etc). At 50% the echoes rotate 90 degrees (front, right, back, left, front, etc.). Negative values will cause the echoes to rotate in the opposite direction.
NEW DYNACABS & CAB BLOCK IMPROVEMENTS
● Added “1x12 Scholz” Dyna-Cab. This is a subset of the 1x12 West Coast Classic Dyna-Cab available in our store, based on a MojoTone™ West Coast cabinet with a 12” Scholz SugarCone™ Classic speaker.
● Added “1x8 Princetone” DynaCab™ captured from a 5F2 Tweed Princeton w/ a very nice sounding 8” Jupiter speaker. Added corresponding Speaker Impedance Curve.
● Added “1x12 Black Magick” DynaCab captured from a Supro Black Magick with a Jensen P12Q speaker. Added corresponding Speaker Impedance Curve. Thanks to Supro for their cooperation on this release!
● Added “8x10 SV Bass” DynaCab captured from an Ampeg SVT. Added corresponding Speaker Impedance Curve. Thanks to Mike "Dr. Bonkers" Santasiero for the fi les from his DynaCab Pack, "Dr. Bonkers 8x10 SBB Bass". If you like the factory DynaCab “sampler” you can purchase the pack for Cab Lab at
https://shop.fractalaudio.comNOTE: Updated auto-impedance mapping in the Amp block to use the new DynaCabs where appropriate.
● Added “Auto Align” switch to the Cab block for DynaCab mode.When ON, individual DynaCabs at any distance are automatically time-aligned to ensure proper phase. When OFF, increasing mic Distance also adds the corresponding delay, simulating real-world microphone behavior where delay increases with mic distance. With either setting, the individual alignment Delay parameters can still be used to add additional delay.
NOTE: The actual delay can be less than the displayed delay as all IR delays are normalized to the shortest delay (so as to minimize overall latency). The Align tab has been changed to display the delay in ms rather than mm to reduce confusion with the Distance parameters. NOTE: Existing presets will have Auto Align set to ON as this was the prior behavior.
PITCH SHIFTER UPDATES
● Improved tracking in the Pitch block, now aligned with Axe-Fx 31.03. This results in better performance for Virtual Capo and other types. The Tracking mode supports NOTES and CHORDS, providing optimized detection for each. The Tracking Adjust parameter has been removed, as this behavior is now handled automatically.
● A new Tracking Mode parameter has been added to the Synth and Ring Mod blocks. It has two options:
○ Guitar – Default behavior, optimized for standard guitar range.
○ Bass – Shifts detection down one octave. In this mode, tracking works down to approximately F♯0.
● Increased upper range of the pitch detectors to approximately F♯6 (High E, 24th fret, whole step bend).
OTHER UPDATES
● Improved Auto-Swell type in Volume block. The new algorithm features a dynamic threshold which tracks the average level of the input signal. The Hysteresis control determines how much the short-term level must drop below the average level to reset the gate. The Threshold control determines the absolute threshold at which the gate will close.
● Improved Envelope Follower in Megatap, Multitap and Plex blocks.
● Added On/Off switch for the Metronome. This can be controlled remotely by setting the desired control source in the MIDI/Remote -> Other menu.
● On the FM3 Mark II, changed the mini LCD contrast function to allow fi ner control over a more usable range.
● Improved “Dwell” in the Spring reverbs.
FIXES
● Changed default mini-LCD contrast setting to 50% for FM3 Mark II types.
● Changed name of “1x12 Brit G12M” impedance curve (obtained from a 1x12 CJ11) to “1x12 Div13 CJ11”.
● Corrected MIDI CC control from Pedal 1 and Pedal 2 not working in fi rmware version 11.0.
● Disabled preset changes while the STORE page is displayed to prevent “behind-the-scenes” preset changes.
● Fixed a gain issue in the Wah block.
● Fixed a resistor value in the Blackglass 7K model. Remastered model as a result.
● Fixed Amp block fi rst stage bias point can get corrupted and produce unwanted distortion.
● Fixed incorrect gain in Colortone Booster and Colortone OD models.
● Fixed Modern Gate type can get stuck closed if input above threshold during boot.
● Fixed some parameters can't return to exactly 0.0 with knob control after going to min or max.
● Fixed wrong Preamp Hardness being loaded for amp models with pentode preamps (i.e., AC-20 EF86).
● Fixed wrong time constant in Herbie models (not signifi cantly audible).
● Fixed wrong value in Deluxe Verb Normal model. Remastered model as a result.
● Fixed a wrong value in Deluxe Verb, Double Verb, Super Verb, Vibroverb, Div/13 FT37, and Double Verb Silverface.
● Improved accuracy of Sustain control vs. position in PI Fuzz models and addressed a stability issue.
● Moved "Mix" tab after "Advanced" tab in Drive and Delay blocks.
● Various other fi xes.
Размещение рекламы