Форум гитаристов

на двуопорном легче играть. Мне понравилось больше чем шести

Не аутентично! А у меня "пунктик! на этом! ) Тараканы'c... 

... и добавил:

У меня 14.4мм 

Зашел я в кое-то веки - опять меряют у кого толще!  Ну ничего не меняется на этом форуме...)

Женщины такие вещи как-то определяют по длине ладони.

я интересовался толщиной грифа))))

примерно то же самое я тебе и говорил..    повторю вопрос - зачем тебе это?. 

Neck shape
Un operaio impegnato nella levigazione del manico. Dalla foto di può capire quanto sia importante la macchina della forma finale del manico (Foto tratta da
Lloyd Chewning shaping a neck (Photo: "Fender: The sound heard 'round the world" by Richard R. Smith
Neck profiles of the Stratocasters changed a lot in the early years. 
1954 and 1955 Stratocasters featured a huge “U” shaped neck, also called baseball bat, thick and large (e.g. .94" depth and 1.60" wide at the first fret).
In the course of 1956 soft “V” shaped necks appeared, and gradually replaced the previous ones, but later in 1957 the profile became very prominent.   These “V” shaped necks are often called boat neck.
Early 1958 necks were flatter and rounded, though they still had a slight “V” feel.  However, in late 1958 a much flatter profile was adopted with thickness steadily below .90" at the 1st fret.
Rosewood-capped necks made after mid-59 were really flat and had a cross-section often below .80" depth!
Early to mid-'60s necks retained similar dimensions, but after 1963 they often featured more shoulder and seemed to be a bit chunkier than 1959 to 1961 necks.  They are universally considered among the best in Fender production, not excessively large and with a shape which is often defined oval “C”.
By the late '60s, both chunkier and flatter profiles were produced, and variances in the neck profiles reached at their peak during the '70s, due to an increased production and machinery wear.  As a rule, however, round clubby necks with a lot of shoulders are the standard on most '70s Stratocasters with measurements like .85" at the 1st fret and .95" at the 12th fret.

DanLAGUNA

At the end of 1981, Fender bought the Austrian Zuckerman carving machine, which could shape eight identical necks at a time as per a master template, and helped Fender to standardize neck profiles.  Stratocaster neck became more consistent, rather flat and with rounded edges. This “flat oval shape”, a sort of gentle “C” profile (e.g. .80" depth), became a standard appointment on '80s and '90s modern Fender guitars and was adopted for the 1987 American Standard Stratocaster.

Вот бы кто Индонезия фендера за $600 выложил тут. Интересно же! 
Уверен, уже есть заказавшие. Колитесь фотками.

F61, тоже видел, ага.

примерно то же самое я тебе и говорил..    повторю вопрос - зачем тебе это?. 

ну как зачем интересно. я люблю толстые грифы. и видел 60-х толстые. плюс опять у Олейника толстый гриф в ролике... судя по переводу, толстые грифы были в конце 60-х

... и добавил:

у меня на страте толщина грифа
2.2 мм на 3 ладу
2,45 мм на 12 ладу

в дюймах не шарю